How To Sight In A Bow Steep By Steep Guide

How To Sight In A Bow

One of the classes solders are being trained at the barracks is to shoot accurately. How confident will you be to hit a target when shooting?  At one point in time even for experienced shooters, they get nervous. If you got a challenge with this adventure, well, then this article will help you learn how to sight in a bow effectively. Sighting using a bow is a process of maximizing your chances to ensure you hit your target. Bow sighting allows the archer to compensate for arrow drop as a result of the pull of gravity through distances and disturbances caused by a firing procedure during the period of aiming.

Inspecting the bow

Just before your sight, you need to ensure that the peep sight and the sight are correctly mounted in the right position. This also leads to ensure that the bow is correctly set up and tuned. If in any case, the bow is hurling arrows in a manner that is not straight, hitting targets will be inconsistent. Fortunately, a good technician will ensure the bow is set up correctly.

Attach the sight

For most sights to be effective, they need screws to be attached. There are pre-drilled holes on the bow which will make the process much light when installing.

Marking the arrows

Marking the arrows makes it easier to know if an arrow is bad. If an arrow keeps going off target when shooting after a couple of times then the problem is not you but it.

Labeling using a tape

By using a lever, place vertically a piece of tape and another horizontally. Also, you can mark these lines on paper and pin them against your target.

Placing the arrow on the rest

This step requires you to loosen the horizontal adjustment of the sight head until the arrow can be placed on a position of releasing all the tension.

Lining up the nocked arrow with the string

The sight is moved until the pins line up with the arrow and the strings. This is achieved by adjusting the site head and for the adequate result; the pin should be set in the center of the sight. However, this varies from an individual to the other.

Realigning the site head

To avoid setbacks, the archer needs to readjust the site head to avoid any frustration. Do not move your head to get the right sight picture. Hold your bow just straight while closing one eye. Examine the bowstring by looking right past it to the front sight. The pins are required to either line up on the strings or be close to it.

Confirming the pin position

Just about 5-yards away from the target, sight in both your left and right by aiming at either the vertical tape or the line. Gauge if to move the pin right or left by shooting 3-5 arrows on the vertical line. Aim both below and above the previous arrow to easily tell which way the bow sight needs to be readjusted. Reshooting can be done till al arrows hit the line or the center of the tape.

Setting target

By using a range finder, which can be found in hunting stores, put marks from the target to shoot from. The distance could be either five yards, ten yards, or even 20 yards.  If you choose a 10 yard, take a straight position, draw the arrow back and shoot.  Do this repetitively until you become accurate. Then you can move back to a longer length.

Increasing and decreasing your target range

While hunting, the game may be at a longer distance, and practicing long targets is a good strategy to get used to such scenarios. Under this, you can adjust the pin instead of the sight. Moreover, you can decrease the target just to prepare your mind to grasp the idea. Much time should be spent to practice for each distance and learning purposes; each distance should have a specific pin. For instance, a 20-yard pin should be 1/8 inch above a 30-yard pin. Using a 40-yard distance the pin should be 1/8 -inch. It will ensure accuracy.

How To Sight In A Bow Short video

Average Shots target

There is no specific amount of shots one can have. The only varying factor is the physical strength and capability of one to shoot. The average shots are around 50 but some individuals have doubled the shots

Fine-tuning the bow

After a session of shots, you may want to visit a technician to fine-tune it but that is unnecessary. Take your time and build your confidence with it and it will take some time before you fine-tune it.

Aiming at a 3-D and 10 ring target

This step is rarely practiced by persons who are learning how to sight in a bow. After conquering long distances, maybe, 60 yards, aiming at the 3-D target is a good bet. Such will make you more accurate. It also helps to build your strength while shooting.

Rear sighting

This sighting is helpful when an additional point of reference is added. There are other types of reference which have different pros and cons. A peep sight is helpful to secure the right anchor point to set a consistent picture. A kisser button is good for shorter shoots since it helps invisibility. The pin sights with a rear extension are an option worthy try though it’s heavier.


The above-explained steps elaborately help a novice to master how to sight in a box. Note that although on a given day you may get the accurate results in comparison with other days, other factors could be a contribution. They include weather and wind conditions. The arrows are light and the atmospheric pressure can contribute to the results. In this case, you may need to make some slight adjustments. Always use the system that you are familiar with. You should not be tied to use a specific distance or method. To ensure your safety have the right backstops and the shooting clearance area. Sight in and hit the shoot!

As an Amazon Associate I earn from qualifying purchases.